Latest NACE NACE-CIP2-001 PDF and Dumps (2026) Free Exam Questions Answers
Pass Your CIP Level 2 NACE-CIP2-001 Exam on Jun 12, 2026 with 100 Questions
NACE-CIP2-001 (Coating Inspector Level 2) Certification Exam is designed to test the knowledge and skills of individuals who are involved in the inspection and quality control of protective coatings. Coating Inspector Level 2 certification is offered by the National Association of Corrosion Engineers (NACE), which is a globally recognized organization that provides training and certification programs in the field of corrosion prevention.
NEW QUESTION # 29
Centrifugal blast cleaning requires:
- A. The use of single use abrasives
- B. A large volume of air to propel the abrasive
- C. Very large nozzles
- D. Well maintained blast wheels
Answer: D
NEW QUESTION # 30
Coating Surveys are legally required:
- A. On food and beverage vessels and can linings
- B. On commercial marine vessels and offshore platforms
- C. On high pressure gas lines and fireproofed structures
- D. On water tanks and potable water pipelines
Answer: B
NEW QUESTION # 31
Non-Conformance Reports are designed to:
- A. Elevate the status of the Inspector
- B. Punish the Contractor for substandard work
- C. To identify items that do not meet the specification requirements
- D. Assist the Owner in negotiating credits from the Contractor
Answer: C
NEW QUESTION # 32
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very low reading
- B. Cold flow or creep
- C. No difference from any other coating
- D. A very high reading
Answer: B
NEW QUESTION # 33
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Investigate to find the source of the odor
- B. Exit the tank and document the incident in your daily report
- C. Don your air supplied respirator and continue the testing
- D. Exit the tank and immediately and report the problem to the nearest safety supervisor
Answer: D
NEW QUESTION # 34
Which is used to calibrate a pH meter?
- A. Distilled water
- B. Standard solvent solution
- C. Deionized water
- D. Standard buffer solution
Answer: D
NEW QUESTION # 35
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Make sure they are the center of attention in all site meetings
- B. Give them as much advance notice as possible about upcoming changes
- C. Implement immediate to get them motivated
- D. Challenge their value to the team and try to get them out of their comfort zone
Answer: B
NEW QUESTION # 36
The Concrete Repair Institute's comparators can be used to assess:
- A. Surface cleanliness prior to coating
- B. Surface profile prior to coating
- C. Compressive and tensile strength prior to coating
- D. Contamination levels prior to coating
Answer: B
NEW QUESTION # 37
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. epoxies.
- B. powder coatings.
- C. inorganic zincs.
- D. urethanes.
Answer: C
NEW QUESTION # 38
When ASIN D 3363 is specified the Inspector must:
- A. Record the highest value attained
- B. Record the two end points identified in the standard
- C. Record the percentage of failure
- D. Use the correct solvent
Answer: B
NEW QUESTION # 39
Galvanizing performs best in which of the following exposures:
- A. pH above 12
- B. pH between 5-10
- C. pH of 13
- D. pH below 4
Answer: B
NEW QUESTION # 40
NACE No.13/ SSPC 6 identifies the use of:
- A. Watterjetting only
- B. Abrasive blasting only
- C. Steam cleaning only
- D. Various methods of cleaning
Answer: D
NEW QUESTION # 41
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Transmission
- C. Gathering
- D. Distribution
Answer: D
NEW QUESTION # 42
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Eddy Current Gauge
- B. Ultra Sonic DFT Gauge
- C. Magnetic Gauge
- D. Tooke Gauge
Answer: D
NEW QUESTION # 43
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Use creative writing to cover over the fact they are missing
- B. Do not complete your report until they can be found
- C. Plainly state in your report that they are missing
- D. Re-create the reports as not much was going on during night shift anyway
Answer: C
NEW QUESTION # 44
Linings are used on the interior of pipelines to
- A. reduce magnetic polarity.
- B. provide protection against soil chemicals.
- C. protect the transported product.
- D. afford limited temperature insulation.
Answer: C
NEW QUESTION # 45
All of these are advantages of using repair patches EXCEPT
- A. special tools or equipment are required.
- B. excellent abrasion resistance.
- C. inert to common acids, alkalis, and solvents.
- D. barrier to moisture and corrosion.
Answer: A
NEW QUESTION # 46
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cold flow or creep
- B. Glue failure
- C. Cohesion failure
- D. Adhesion failure
Answer: A
NEW QUESTION # 47
Examples of non-ferrous metals include
Select All that Apply:
- A. copper
- B. iron
- C. aluminum
- D. mild steel.
Answer: A,C
NEW QUESTION # 48
In which type of concrete are laitance commonly encountered?
- A. Gunite
- B. Glass fiber cement
- C. Concrete block (poured with a form)
- D. Poured (wet cast)
Answer: D
NEW QUESTION # 49
Thermal Spray coatings provide:
- A. Sacrificial protection
- B. Thermal protection
- C. Barrier protection
- D. Inhibitive protection
Answer: A
NEW QUESTION # 50
When observing fabrication defects the NACE Inspector should:
- A. Write an NCR and call the fabricator
- B. Consult the specification to determine how they should be treated
- C. Stop the job immediately
- D. Require they be corrected prior to coating
Answer: B
NEW QUESTION # 51
......
NACE-CIP2-001 exam is a comprehensive test that evaluates the candidate's knowledge of surface preparation, coating application, and post-application inspection. It assesses the candidate's ability to evaluate coating failures, identify coating defects, and recommend corrective measures to ensure that the coating meets the required standards.
NACE-CIP2-001 Dumps for CIP Level 2 Certified Exam Questions and Answer: https://dumpstorrent.exam4pdf.com/NACE-CIP2-001-dumps-torrent.html
